Electro-Mechanical Technicians
Xenair Nig Ltd
Lagos State, nigeria
9d ago
source : Jiji.ng

Job Summary : Operate, Test, Maintain, Or Calibrate Unmanned, Automated, Servo-Mechanical, Or Electromechanical Equipment.

May Operate Unmanned Submarines, Aircraft, Or Other Equipment At Worksites, Such As Oil Rigs, Deep Ocean Exploration, Or Hazardous Waste Removal.

May Assist Engineers In Testing And Designing Robotics Equipment. Job Tasks Adjust Doors To Open Or Close With The Correct Amount Of Effort Or Make Simple Adjustments To Electric Openers.

Wind Large Springs With Upward Motion Of Arm. Inspect Job Sites, Assessing Headroom, Side Room, Or Other Conditions To Determine Appropriateness Of Door For A Given Location.

Collect Payment Upon Job Completion. Complete Required Paperwork, Such As Work Orders, According To Services Performed Or Required.

Fasten Angle Iron Back-Hangers To Ceilings And Tracks, Using Fasteners Or Welding Equipment. Repair Or Replace Worn Or Broken Door Parts, Using Hand Tools.

Carry Springs To Tops Of Doors, Using Ladders Or Scaffolding, And Attach Springs To Tracks To Install Spring Systems. Set Doors Into Place Or Stack Hardware Sections Into Openings After Rail Or Track Installation.

Remove Or Disassemble Defective Automatic Mechanical Door Closers, Using Hand Tools. Install Door Frames, Rails, Steel Rolling Curtains, Electronic-

Eye Mechanisms, Or Electric Door Openers And Closers, Using Power Tools, Hand Tools, And Electronic Test Equipment. Apply Hardware To Door Sections, Such As Drilling Holes To Install Locks.

Order Replacement Springs, Sections, Or Slats. Assemble And Fasten Tracks To Structures Or Bucks, Using Impact Wrenches Or Welding Equipment.

Run Low Voltage Wiring On Ceiling Surfaces, Using Insulated Staples. Cut Door Stops Or Angle Irons To Fit Openings. Study Blueprints And Schematic Diagrams To Determine Appropriate Methods Of Installing Or Repairing Automated Door Openers.

  • Bore Or Cut Holes In Flooring As Required For Installation, Using Hand Or Power Tools. Set In And Secure Floor Treadles For Door Activating Mechanisms;
  • Then Connect Power Packs And Electrical Panelboards To Treadles. Operate Lifts, Winches, Or Chain Falls To Move Heavy Curtain Doors.

    Lubricate Door Closer Oil Chambers And Pack Spindles With Leather Washers. Install Dock Seals, Bumpers, Or Shelters. Fabricate Replacements For Worn Or Broken Parts, Using Welders, Lathes, Drill Presses, Or Shaping Or Milling Machines.

    Clean Door Closer Parts, Using Caustic Soda, Rotary Brushes, Or Grinding Wheels. Cover Treadles With Carpeting Or Other Floor Covering Materials And Test Systems By Operating Treadles.

    Job Requirements : Experience : Some Previous Work-Related Skill, Knowledge, Or Experience May Be Helpful In These Occupation.

    Education : These Occupations Usually Require A High School Diploma And May Require Some Vocational Training Or Job-Related Course Work.

    Bachelor'S Degree Could Be Needed An Added Advantage. Application Method : Applicants Can Apply By Using Any Of The Under Listed Methods : Forward Your Application Letter, Cv And A Page Resume To Xenair Outlook.

    Com Comment Your Cv Or Resume To The Comment Box. Upload Your Cv Directly And Click Apply. Calls Are Only Allowed Between The Hours Of 8Am -

    5.30Pm Mon Sat Only. Please Note That Only Short-Listed Candidates Will Be Contacted.

    Apply
    Add to favorites
    Remove from favorites
    Apply
    My Email
    By clicking on "Continue", I give neuvoo consent to process my data and to send me email alerts, as detailed in neuvoo's Privacy Policy . I may withdraw my consent or unsubscribe at any time.
    Continue
    Application form